欧美日韩福利,国产一区久久,亚洲精品99久久久久中文字幕

// SI114.h
// Code for the Modern Device Pulse Sensor
// Based on the SI1143 chip
// Also includes subset of JeeLabs Ports library - thanks JCW!
// paul@moderndevice.com 6-27-2012
#include "SI114.h"
#include <avr/sleep.h>
#include <util/atomic.h>
// flag bits sent to the receiver
#define MODE_CHANGE 0x80 // a pin mode was changed
#define DIG_CHANGE 0x40 // a digital output was changed
#define PWM_CHANGE 0x30 // an analog (pwm) value was changed on port 2..3
#define ANA_MASK 0x0F // an analog read was requested on port 1..4
byte PulsePlug::readParam (byte addr) {
// read from parameter ram
send();
write(PulsePlug::COMMAND);
write(0x80 | addr); // PARAM_QUERY
stop();
delay(10);
return getReg(PulsePlug::PARAM_RD);
}
byte PulsePlug::getReg (byte reg) {
// get a register
send();
write(reg);
receive();
byte result = read(1);
stop();
delay(10);
return result;
}
void PulsePlug::setReg (byte reg, byte val) {
// set a register
send();
write(reg);
write(val);
stop();
delay(10);
}
void PulsePlug::initPulsePlug(){
PulsePlug::setReg(PulsePlug::HW_KEY, 0x17);
// pulsePlug.setReg(PulsePlug::COMMAND, PulsePlug::RESET_Cmd);
Serial.print("PART: ");
Serial.print(PulsePlug::getReg(PulsePlug::PART_ID));
Serial.print(" REV: ");
Serial.print(PulsePlug::getReg(PulsePlug::REV_ID));
Serial.print(" SEQ: ");
Serial.println(PulsePlug::getReg(PulsePlug::SEQ_ID));
PulsePlug::setReg(PulsePlug::INT_CFG, 0x03); // turn on interrupts
PulsePlug::setReg(PulsePlug::IRQ_ENABLE, 0x10); // turn on interrupt on PS3
PulsePlug::setReg(PulsePlug::IRQ_MODE2, 0x01); // interrupt on ps3 measurement
PulsePlug::setReg(PulsePlug::MEAS_RATE, 0x84); // see datasheet
PulsePlug::setReg(PulsePlug::ALS_RATE, 0x08); // see datasheet
PulsePlug::setReg(PulsePlug::PS_RATE, 0x08); // see datasheet
PulsePlug::setReg(PulsePlug::PS_LED21, 0x66 ); // LED current for LEDs 1 (red) & 2 (IR1)
PulsePlug::setReg(PulsePlug::PS_LED3, 0x06); // LED current for LED 3 (IR2)
Serial.print( "PS_LED21 = ");
Serial.println(PulsePlug::getReg(PulsePlug::PS_LED21), BIN);
Serial.print("CHLIST = ");
Serial.println(PulsePlug::readParam(0x01), BIN);
PulsePlug::writeParam(PulsePlug::PARAM_CH_LIST, 0x77); // all measurements on
// increasing PARAM_PS_ADC_GAIN will increase the LED on time and ADC window
// you will see increase in brightness of visible LED's, ADC output, & noise
// datasheet warns not to go beyond 4 because chip or LEDs may be damaged
PulsePlug::writeParam(PulsePlug::PARAM_PS_ADC_GAIN, 0x00);
PulsePlug::writeParam(PulsePlug::PARAM_PSLED12_SELECT, 0x21); // select LEDs on for readings see datasheet
PulsePlug::writeParam(PulsePlug::PARAM_PSLED3_SELECT, 0x04); // 3 only
PulsePlug::writeParam(PulsePlug::PARAM_PS1_ADCMUX, 0x03); // PS1 photodiode select
PulsePlug::writeParam(PulsePlug::PARAM_PS2_ADCMUX, 0x03); // PS2 photodiode select
PulsePlug::writeParam(PulsePlug::PARAM_PS3_ADCMUX, 0x03); // PS3 photodiode select
PulsePlug::writeParam(PulsePlug::PARAM_PS_ADC_COUNTER, B01110000); // B01110000 is default
PulsePlug::setReg(PulsePlug::COMMAND, PulsePlug::PSALS_AUTO_Cmd); // starts an autonomous read loop
}
void PulsePlug::setLEDcurrents(byte LED1, byte LED2, byte LED3){
/* VLEDn = 1 V, PS_LEDn = 0001 5.6
VLEDn = 1 V, PS_LEDn = 0010 11.2
VLEDn = 1 V, PS_LEDn = 0011 22.4
VLEDn = 1 V, PS_LEDn = 0100 45
VLEDn = 1 V, PS_LEDn = 0101 67
VLEDn = 1 V, PS_LEDn = 0110 90
VLEDn = 1 V, PS_LEDn = 0111 112
VLEDn = 1 V, PS_LEDn = 1000 135
VLEDn = 1 V, PS_LEDn = 1001 157
VLEDn = 1 V, PS_LEDn = 1010 180
VLEDn = 1 V, PS_LEDn = 1011 202
VLEDn = 1 V, PS_LEDn = 1100 224
VLEDn = 1 V, PS_LEDn = 1101 269
VLEDn = 1 V, PS_LEDn = 1110 314
VLEDn = 1 V, PS_LEDn = 1111 359 */
LED1 = constrain(LED1, 0, 15);
LED2 = constrain(LED2, 0, 15);
LED3 = constrain(LED3, 0, 15);
PulsePlug::setReg(PulsePlug::PS_LED21, (LED2 << 4) | LED1 );
PulsePlug::setReg(PulsePlug::PS_LED3, LED3);
}
void PulsePlug::setLEDdrive(byte LED1pulse, byte LED2pulse, byte LED3pulse){
// this sets which LEDs are active on which pulses
// any or none of the LEDs may be active on each PulsePlug
//000: NO LED DRIVE
//xx1: LED1 Drive Enabled
//x1x: LED2 Drive Enabled (Si1142 and Si1143 only. Clear for Si1141)
//1xx: LED3 Drive Enabled (Si1143 only. Clear for Si1141 and Si1142)
// example setLEDdrive(1, 2, 5); sets LED1 on pulse 1, LED2 on pulse 2, LED3, LED1 on pulse 3
PulsePlug::writeParam(PulsePlug::PARAM_PSLED12_SELECT, (LED1pulse << 4) | LED2pulse ); // select LEDs on for readings see datasheet
PulsePlug::writeParam(PulsePlug::PARAM_PSLED3_SELECT, LED3pulse);
}
void PulsePlug::fetchData () {
// read out all result registers as lsb-msb pairs of bytes
send();
write(PulsePlug::RESPONSE);
receive();
byte* p = (byte*) &resp;
for (byte i = 0; i < 16; ++i)
p[i] = read(0);
read(1); // just to end cleanly
stop();
}
void PulsePlug::fetchLedData() {
// read only the LED registers as lsb-msb pairs of bytes
send();
write(PulsePlug::PS1_DATA0);
receive();
byte* q = (byte*) &ps1;
for (byte i = 0; i < 6; ++i)
q[i] = read(0);
read(1); // just to end cleanly
stop();
}
void PulsePlug::writeParam (byte addr, byte val) {
// write to parameter ram
send();
write(PulsePlug::PARAM_WR);
write(val);
// auto-increments into PulsePlug::COMMAND
write(0xA0 | addr); // PARAM_SET
stop();
delay(10);
}
uint16_t Port::shiftRead(uint8_t bitOrder, uint8_t count) const {
uint16_t value = 0, mask = bit(LSBFIRST ? 0 : count - 1);
for (uint8_t i = 0; i < count; ++i) {
digiWrite2(1);
delayMicroseconds(5);
if (digiRead())
value |= mask;
if (bitOrder == LSBFIRST)
mask <<= 1;
else
mask >>= 1;
digiWrite2(0);
delayMicroseconds(5);
}
return value;
}
void Port::shiftWrite(uint8_t bitOrder, uint16_t value, uint8_t count) const {
uint16_t mask = bit(LSBFIRST ? 0 : count - 1);
for (uint8_t i = 0; i < count; ++i) {
digiWrite((value & mask) != 0);
if (bitOrder == LSBFIRST)
mask <<= 1;
else
mask >>= 1;
digiWrite2(1);
digiWrite2(0);
}
}
PortI2C::PortI2C (uint8_t num, uint8_t rate)
: Port (num), uswait (rate)
{
sdaOut(1);
mode2(OUTPUT);
sclHi();
}
uint8_t PortI2C::start(uint8_t addr) const {
sclLo();
sclHi();
sdaOut(0);
return write(addr);
}
void PortI2C::stop() const {
sdaOut(0);
sclHi();
sdaOut(1);
}
uint8_t PortI2C::write(uint8_t data) const {
sclLo();
for (uint8_t mask = 0x80; mask != 0; mask >>= 1) {
sdaOut(data & mask);
sclHi();
sclLo();
}
sdaOut(1);
sclHi();
uint8_t ack = ! sdaIn();
sclLo();
return ack;
}
uint8_t PortI2C::read(uint8_t last) const {
uint8_t data = 0;
for (uint8_t mask = 0x80; mask != 0; mask >>= 1) {
sclHi();
if (sdaIn())
data |= mask;
sclLo();
}
sdaOut(last);
sclHi();
sclLo();
if (last)
stop();
sdaOut(1);
return data;
}
bool DeviceI2C::isPresent () const {
byte ok = send();
stop();
return ok;
}
byte MilliTimer::poll(word ms) {
byte ready = 0;
if (armed) {
word remain = next - millis();
// since remain is unsigned, it will overflow to large values when
// the timeout is reached, so this test works as long as poll() is
// called no later than 5535 millisecs after the timer has expired
if (remain <= 60000)
return 0;
// return a value between 1 and 255, being msecs+1 past expiration
// note: the actual return value is only reliable if poll() is
// called no later than 255 millisecs after the timer has expired
ready = -remain;
}
set(ms);
return ready;
}
word MilliTimer::remaining() const {
word remain = armed ? next - millis() : 0;
return remain <= 60000 ? remain : 0;
}
void MilliTimer::set(word ms) {
armed = ms != 0;
if (armed)
next = millis() + ms - 1;
}
Scheduler::Scheduler (byte size) : maxTasks (size), remaining (~0) {
byte bytes = size * sizeof *tasks;
tasks = (word*) malloc(bytes);
memset(tasks, 0xFF, bytes);
}
Scheduler::Scheduler (word* buf, byte size) : tasks (buf), maxTasks (size), remaining(~0) {
byte bytes = size * sizeof *tasks;
memset(tasks, 0xFF, bytes);
}
char Scheduler::poll() {
// all times in the tasks array are relative to the "remaining" value
// i.e. only remaining counts down while waiting for the next timeout
if (remaining == 0) {
word lowest = ~0;
for (byte i = 0; i < maxTasks; ++i) {
if (tasks[i] == 0) {
tasks[i] = ~0;
return i;
}
if (tasks[i] < lowest)
lowest = tasks[i];
}
if (lowest != ~0) {
for (byte i = 0; i < maxTasks; ++i) {
if(tasks[i] != ~0) {
tasks[i] -= lowest;
}
}
}
remaining = lowest;
} else if (remaining == ~0) //remaining == ~0 means nothing running
return -2;
else if (ms100.poll(100))
--remaining;
return -1;
}
void Scheduler::timer(byte task, word tenths) {
// if new timer will go off sooner than the rest, then adjust all entries
if (tenths < remaining) {
word diff = remaining - tenths;
for (byte i = 0; i < maxTasks; ++i)
if (tasks[i] != ~0)
tasks[i] += diff;
remaining = tenths;
}
tasks[task] = tenths - remaining;
}
void Scheduler::cancel(byte task) {
tasks[task] = ~0;
}

復制代碼

久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费