問題是這樣的：
字體取模后，導入程序中去。顯示時是反的:比如：專業制作 變成：作制業專。取模軟件里也水平翻轉了也不行。每次要用【文字倒寫軟件】：變成：作制業專
輸入到取模軟件里，再水平翻轉，然后生產字模數據。再導入程序中，真是N麻煩啊！有哪位高手幫我指點一下，本人是學生。謝謝了！
付程序：
#include " reg51.h"
#define BLKN 8
#define TOTAL 4//注明顯示字個數//
#define CONIO P0//定義輸出端口//
sbit G = CONIO^7;//G1=P1.7=8腳//
sbit CLK = CONIO^6;//RCLK=P1.6=7腳//
sbit SCLR = CONIO^5;//SRCLK=P1.5=6腳//
unsigned char idata dispram[(BLKN/2)*32]={0};//顯示區緩存,4字共*32單元//
unsigned char code Bmp[][32]={
0xFE,0xFF,0xFE,0xFF,0xC0,0x07,0xFD,0xFF,0xFD,0xFF,0x00,0x01,0xFB,0xFF,0xF7,0xDF,
0xF0,0x0F,0xFF,0xDF,0xFF,0xBF,0xFD,0x7F,0xFE,0xFF,0xFF,0x7F,0xFF,0xBF,0xFF,0xFF,/*"專",0*/
0xFB,0xBF,0xFB,0xBF,0xFB,0xBF,0xFB,0xBB,0xBB,0xB9,0xDB,0xB3,0xDB,0xB7,0xEB,0xAF,
0xE3,0xAF,0xEB,0x9F,0xFB,0xBF,0xFB,0xBF,0xFB,0xBB,0x00,0x01,0xFF,0xFF,0xFF,0xFF,/*"業",1*/
0xDB,0xFB,0xCB,0xFB,0xDB,0xDB,0xC0,0x5B,0xBB,0xDB,0xFB,0xDB,0x80,0x5B,0xFB,0xDB,
0xC0,0x5B,0xDB,0x5B,0xDB,0x5B,0xDB,0x5B,0xDB,0x7B,0xD8,0x7B,0xFA,0xEB,0xFB,0xF7,/*"制",2*/
0xF7,0x7F,0xF3,0x7F,0xF6,0xFF,0xEC,0x01,0xED,0x7F,0xCB,0x77,0xAF,0x03,0x6F,0x7F,
0xEF,0x7F,0xEF,0x7B,0xEF,0x01,0xEF,0x7F,0xEF,0x7F,0xEF,0x7F,0xEF,0x7F,0xEF,0x7F,/*"作",3*/
};
/****延時函數（約1MS）**********/
void delay(unsigned int dt)
{
register unsigned char bt;
for(;dt;dt--)
for(bt=0;bt<255;bt++);
}
/******主函數********/
void main (void)
{
register unsigned char q,w ,i,j,k; //i,j,k,l,q,w;
//初始化
SCON = 0x00;
TMOD = 0x01;
TR0 = 1;
CONIO = 0x3f;
IE = 0x82;
while(1)
{
delay(2000);//2S
問題就是在下面程序不知怎么更改：才能把字體顯示順序正常！請求幫忙！
// 卷簾顯示文字,每次字數為BLKN/2,共顯示TOTAL*2/BLKN次
for(w=0;w< TOTAL*2/BLKN;w++)
{
for(i=0;i<32;i++)
{
for(q=0;q<BLKN/2;q++){dispram[i+q*32]=Bmp[q+w*BLKN/2];}
if(i%2) delay(100);//移動時間
}
delay(2000);//停止時間
}
//第二種顯示效果,向上滾屏,每次BLKN/2個字
for(i=0;i<TOTAL*2/BLKN;i++)
{
for(j=0;j<16;j++)
{
for(k=0;k<15;k++)
{
for(q=0;q<BLKN/2;q++)
{dispram[k*2+q*32] = dispram[(k+1)*2+q*32];
dispram[k*2+1+q*32] = dispram[(k+1)*2+1+q*32];}
}
for(q=0;q<BLKN/2;q++)
{dispram[30+q*32] = Bmp[q+i*BLKN/2][j*2];
dispram[31+q*32] = Bmp[q+i*BLKN/2][j*2+1];}
delay(100);
}
delay(1000); //滾動暫停
以下是左移方式時，字又正常！
}
for(i=0;i<TOTAL;i++)
{
for(j=2;j>0;j--)
for(k=0;k<8;k++)
{
for(l=0;l<16;l++)
{
for(q=0;q<BLKN/2;q++)
{
dispram[l*2+1+q*32]= dispram[l*2+1+q*32]>>1| dispram[l*2+q*32]<<7;
if(q==0) dispram[l*2+q*32]= dispram[l*2+q*32]>>1|Bmp[l*2+j-1]<<(7-k);
else dispram[l*2+q*32]= dispram[l*2+q*32]>>1| dispram[l*2+1+(q-1)*32]<<7;
}
}
delay(100);//移動時間
| 歡迎光臨 (http://www.zg4o1577.cn/bbs/) | Powered by Discuz! X3.1 |