久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费

標題: 新手心得 : HAL 練習 STM32F030F4P6 [打印本頁]

作者: jj449 時間: 2018-11-1 07:13
標題: 新手心得 : HAL 練習 STM32F030F4P6

初始運作只需三個外圍器件， SWDIO跟 SWCLK 要接 10K 電阻(手上沒有10K，我用8.2K 運作也是OK的)，Boot0接560R接地即可運作。VDDA，VDD，VSS(GND) ，Boot0(GND) 都要適當接好，不要懸空。如果要使用 I2C , SPI ，畫板時記得給上 pull-up R ，並預先考慮兩個以上I2C 或 SPI devices的狀況，預留線路，應該就能使用愉快。唯一的困難是像我這樣的新手，要手焊 tssop20 有點難，需要練習一下。 ram看起來不大，不過一般應用應該是夠了，除非遇到像需要點陣字表這類的東西，很耗費存儲的，那就看情況是否需要加外部存儲。

32位元 mcu , 32 !! 32 !! 32 !! up to 48MHZ

16kB of flash and 4kB of SRAM , I2C x1 , SPI x 1 , USART x 2 , tssop20 package , with internal clock (HSI)

cheap , stable , easy to use .

參考

en.CD00167594.pdf (3.52 MB, 下載次數: 36)

VDD , VDDA –> 3.3V (VDDA must >= VDD)

VSS –> GND

BOOT0 –> R —> GND

SWDIO –> 10K –> adaptor

SWCLK –> 10K –> adaptor

diy a breakout board ?

hardiest part is soldering mcu chip onto pcb (for me) , need a little practice ..

easiest way to download sketch is stlink-v2, so simplest HAL in cubeMX looks like this :

here , we use cubeMx + sw4stm32 as development tool .

1. in sw4stm32 , create a workspace

2. in cubeMx , assign project location in that workspace , and check “Generate Under Root “

3. after generating code , click “open” , then sw4stm32 start ! enjoy !

if encounter any problem when flash program , in sw4stm32 check project debug option .

project -> properties -> debug/run setting-> edit (or new)

here , make sure Interface = SWD , Reset = Software , and Frequency must equal to adaptor’s frequency 。

if we want to use I2C device , ex: I2C oled , in cubeMx must configure it right .

done ! now can try to upload 1st program .

Using OLED 1306 :

driver : https://github.com/4ilo/ssd1306-stm32HAL

copy inc/ssd1306.h & inc/font.h to inc/

copy src/ssd1306.c & src/font.c to src/

modify all stm32fXXX_hal.h to ur _hal.h

done !

if u want to use UART to upload firmware :

VDDA should be connected to power, otherwise chip is in reset state. If package has VSSA – it also should be connected (to GND).

To enter boot mode it is sufficient to connect BOOT0 to power during reset. Do not get confused with absent BOOT1 pin – it is in proper state internally. 設計的時候，就直接把CPU的BOOT1引腳接地（始終為0），就沒有BOOT1引腳了

pin 16 (VDD) to +3.3
pin 5 (VDDA) to +3.3
pin 15 (GND) to GND
pin 1 (BOOT0) to +3.3
pin 4 (RESET) to GND, temporarily
pin 17 (USART1_TX) to RX of the FTDI-cable
pin 18 (USART1_RX) to TX of the FTDI-cable

作者: cooleaf 時間: 2019-8-16 17:43
樓主厲害呀！

歡迎光臨 (http://www.zg4o1577.cn/bbs/)