伊人av超碰久久久麻豆,日韩精品,国产乱老熟视频网88av

#include <reg52.h>
#include <intrins.h>
#include <absacc.h>
#include <math.h>
#include "0832.h"
#define uchar unsigned char
#define uint unsigned int
#include "eeprom52.h"
sbit DATA = P3^7; //溫濕度
sbit E=P2^5; //1602使能引腳
sbit RS=P2^7; //1602數據/命令選擇引腳
sbit RW=P2^6;
sbit K1=P1^3;//設置鍵
sbit K2=P1^4;//加
sbit K3=P1^5;//減
sbit LED1=P3^1; //煙霧報警
sbit LED2=P3^2; //溫度上限
sbit LED3=P3^3; //溫度下限
sbit LED4=P3^4; //濕度上限
sbit LED5=P3^5; //濕度下限
sbit alarm=P3^0; //蜂鳴器
uchar U8FLAG,U8temp,U8comdata,U8RH_data_H_temp,U8RH_data_L_temp,U8T_data_H_temp,U8T_data_L_temp,U8checkdata_temp;
uchar U8RH_data_H,U8RH_data_L,U8T_data_H,U8T_data_L,U8checkdata;
uchar Mode,humidity,temperature,smog;
bit BJ_LED1=1,BJ_LED2=1,BJ_LED3=1,BJ_LED4=1,BJ_LED5=1,BJ_LED6=1; //定義LED報警變量
bit bdata FlagStartRH;
uchar flag ;//記錄當前設置狀態
uint count;
//定時器0初始化
void Timer0_Init()
{
ET0 = 1; //允許定時器0中斷
TMOD = 0x11; //定時器工作方式選擇
TL0 = 0xFF;
TH0 = 0x4B; //定時器賦予初值
TH1=0xdc;
TL1=0x00;
ET1=1;
TR0 = 1; //啟動定時器
}
//定時器0中斷
void Timer0_ISR (void) interrupt 1 using 0
{
uchar RHCounter;
TL0 = 0xFF;
TH0 = 0x4B; //定時器賦予初值
RHCounter++;
if (RHCounter >= 15)
{
FlagStartRH = 1;
RHCounter = 0;
}
}
void Delay1(uint j)
{
uchar i;
for(;j>0;j--)
{
for(i=0;i<27;i++);
}
}
void Delay_10us(void)
{
uchar i;
i--;
i--;
i--;
i--;
i--;
i--;
}
void delay_ms(uint z) //延時函數
{
uint x,y;
for(x=z;x>0;x--)
for(y=121;y>0;y--); //約1ms
}
void COM(void)
{
uchar i;
for(i=0;i<8;i++)
{
U8FLAG=2;
while((!DATA)&&U8FLAG++);
Delay_10us();
Delay_10us();
Delay_10us();
U8temp=0;
if(DATA)U8temp=1;
U8FLAG=2;
while((DATA)&&U8FLAG++);
//超時則跳出for循環
if(U8FLAG==1)break;
//判斷數據位是0還是1
// 如果高電平高過預定0高電平值則數據位為 1
U8comdata<<=1;
U8comdata|=U8temp; //0
}//rof
}
//--------------------------------
//-----溫濕度讀取子程序 ------------
//--------------------------------
//----以下變量均為全局變量--------
//----溫度高8位== U8T_data_H------
//----溫度低8位== U8T_data_L------
//----濕度高8位== U8RH_data_H-----
//----濕度低8位== U8RH_data_L-----
//----校驗 8位 == U8checkdata-----
//----調用相關子程序如下----------
//---- Delay();, Delay_10us();,COM();
//--------------------------------
uchar RH(void)
{
//主機拉低18ms
DATA=0;
Delay1(180); //原來為5
DATA=1;
//總線由上拉電阻拉高主機延時20us
Delay_10us();
Delay_10us();
Delay_10us();
Delay_10us();
//主機設為輸入判斷從機響應信號
DATA=1;
//判斷從機是否有低電平響應信號如不響應則跳出，響應則向下運行
if(!DATA) //T !
{
U8FLAG=2;
//判斷從機是否發出 80us 的低電平響應信號是否結束
while((!DATA)&&U8FLAG++);
U8FLAG=2;
//判斷從機是否發出 80us 的高電平，如發出則進入數據接收狀態
while((DATA)&&U8FLAG++);
//數據接收狀態
COM();
U8RH_data_H_temp=U8comdata;
COM();
U8RH_data_L_temp=U8comdata;
COM();
U8T_data_H_temp=U8comdata;
COM();
U8T_data_L_temp=U8comdata;
COM();
U8checkdata_temp=U8comdata;
DATA=1;
//數據校驗
U8temp=(U8T_data_H_temp+U8T_data_L_temp+U8RH_data_H_temp+U8RH_data_L_temp);
if(U8temp==U8checkdata_temp)
{
U8RH_data_H=U8RH_data_H_temp;
U8RH_data_L=U8RH_data_L_temp;
U8T_data_H=U8T_data_H_temp;
U8T_data_L=U8T_data_L_temp;
U8checkdata=U8checkdata_temp;
}
return 1;
}
else //傳感器不響應
{
return 0;
}
}
/********************************************************************
* 文件名：液晶1602顯示.c
* 描述 : 該程序?qū)崿F(xiàn)了對液晶1602的控制。
***********************************************************************/
/********************************************************************
* 名稱 : delay()
* 功能 : 延時,延時時間大概為140US。
* 輸入 : 無
* 輸出 : 無
***********************************************************************/
void delay()
{
int i,j;
for(i=0; i<=10; i++)
for(j=0; j<=2; j++);
}
/********************************************************************
* 名稱 : enable(uchar del)
* 功能 : 1602命令函數
* 輸入 : 輸入的命令值
* 輸出 : 無
***********************************************************************/
void write_1602com(uchar del)
{
P0 = del;
RS = 0;
E = 1;
delay();
E = 0;
delay();
}
/********************************************************************
* 名稱 : write(uchar del)
* 功能 : 1602寫數據函數
* 輸入 : 需要寫入1602的數據
* 輸出 : 無
***********************************************************************/
void write_1602dat(uchar del)
{
P0 = del;
RS = 1;
E = 1;
delay();
E = 0;
delay();
}
/********************************************************************
* 名稱 : L1602_init()
* 功能 : 1602初始化，請參考1602的資料
* 輸入 : 無
* 輸出 : 無
***********************************************************************/
void L1602_init(void)
{
write_1602com(0x38);
write_1602com(0x0c);
write_1602com(0x06);
write_1602com(0x01); //清屏要放在最后
delay_ms(2);
}
void display()
{
write_1602com(0x83);
write_1602dat(temperature%100/10+0x30);
write_1602dat(temperature%100%10+0x30);
write_1602com(0x8c);
write_1602dat(humidity%100/10+0x30);
write_1602dat(humidity%100%10+0x30);
write_1602com(0xc3);
write_1602dat(smog%100/10+0x30);
write_1602dat(smog%100%10+0x30);
write_1602com(0x85);
write_1602dat(0xdf);
}
void display_1()
{
write_1602com(0x83);
write_1602dat(TH%100/10+0x30);
write_1602dat(TH%100%10+0x30);
write_1602com(0x8c);
write_1602dat(TL%100/10+0x30);
write_1602dat(TL%100%10+0x30);
write_1602com(0xc3);
write_1602dat(HH%100/10+0x30);
write_1602dat(HH%100%10+0x30);
write_1602com(0xcc);
write_1602dat(HL%100/10+0x30);
write_1602dat(HL%100%10+0x30);
}
void write_string(uchar * str)
{
while( * str)
{
write_1602dat(* str);
str++;
}
}
/***按鍵函數***/
void KEY()
{
if(K1==0)
{
Delay1(200);
if(K1==0)
{
flag++;
if(flag==1)
{
write_1602com(0x80);
write_string("TH: C TL: C");
write_1602com(0xc0);
write_string("HH: % HL: % ");
write_1602com(0x85);
write_1602dat(0xdf);
write_1602com(0x8e);
write_1602dat(0xdf);
display_1();
write_1602com(0x84);
write_1602com(0x0f);
}
else if(flag==2)
write_1602com(0x8d);
else if(flag==3)
write_1602com(0xc4);
else if(flag==4)
write_1602com(0xcd);
else if(flag==5)
{
write_1602com(0xc0);
write_string(" ");
write_1602com(0x80);
write_string("Sg: mg/m3 ");
write_1602com(0x83);
write_1602dat(SM/10+0x30);
write_1602dat(SM%10+0x30);
write_1602com(0x84);
}
else
{
write_1602com(0x80);
write_string("Te: C Hu: % ");
write_1602com(0xc0);
write_string("Sg: mg/m3 ");
write_1602com(0x85);
write_1602dat(0xdf);
display();
write_1602com(0x0c);
flag=0;
write_eeprom();
}
while(!K1);
}
}
if(K2==0)
{
Delay1(200);
if(K2==0)
{
switch (flag)
{
case 1: TH++;if(TH>99) TH=0;if(TH<=TL) TH=TL+1; write_1602com(0x83);write_1602dat(TH/10+0x30);write_1602dat(TH%10+0x30); write_1602com(0x84);break;
case 2: TL++;if(TL>98) TL=0; if(TL>=TH) TL=TH-1; write_1602com(0x8c);write_1602dat(TL/10+0x30);write_1602dat(TL%10+0x30);write_1602com(0x8d); break;
case 3: HH++;if(HH>99) HH=0; if(HH<=HL) HH=HL+1;write_1602com(0xc3);write_1602dat(HH/10+0x30);write_1602dat(HH%10+0x30); write_1602com(0xc4);break;
case 4: HL++;if(HL>98) HL=0; if(HL>=HH) HL=HH-1; write_1602com(0xcc);write_1602dat(HL/10+0x30);write_1602dat(HL%10+0x30); write_1602com(0xcd);break;
case 5: SM++;if(SM>9) SM=0; write_1602com(0x83);write_1602dat(SM/10+0x30);write_1602dat(SM%10+0x30);write_1602com(0x84); break;
}
while(!K2);
}
}
if(K3==0)
{
Delay1(200);
if(K3==0)
{
switch (flag)
{
case 1: TH--;if(TH>99) TH=99; if(TH<=TL) TH=TL+1; write_1602com(0x83);write_1602dat(TH/10+0x30);write_1602dat(TH%10+0x30); write_1602com(0x84);break;
case 2: TL--;if(TL>99) TL=98;if(TL>=TH) TL=TH-1; write_1602com(0x8c);write_1602dat(TL/10+0x30);write_1602dat(TL%10+0x30);write_1602com(0x8d); break;
case 3: HH--;if(HH>99) HH=99; if(HH<=HL) HH=HL+1; write_1602com(0xc3);write_1602dat(HH/10+0x30);write_1602dat(HH%10+0x30); write_1602com(0xc4);break;
case 4: HL--;if(HL>99) HL=98;if(HL>=HH) HL=HH-1; write_1602com(0xcc);write_1602dat(HL/10+0x30);write_1602dat(HL%10+0x30); write_1602com(0xcd);break;
case 5: SM--;if(SM>99) SM=9; write_1602com(0x83);write_1602dat(SM/10+0x30);write_1602dat(SM%10+0x30);write_1602com(0x84); break;
}
while(!K3);
}
}
}
void Onealarm()
{
alarm=0;
Delay1(200);
alarm=1;
}
void dis_init()
{
unsigned char pp=0;
write_1602com(0x80); //進入設置狀態顯示
write_string("Welcome to use "); //設置狀態第一行顯示
write_1602com(0xc0); //選中第二行
write_string("Please waiting.."); //設置狀態第二行顯示
P3=0xFE;
delay_ms(500);
for(pp=0;pp<8;pp++)
{
P3=_crol_(P3,1);
delay_ms(100);
}
P3=0x7F;
for(pp=0;pp<8;pp++)
{
P3=_cror_(P3,1);
delay_ms(100);
}
alarm=1;
LED1=LED2=LED3=LED4=LED5=0;
delay_ms(2000);
}
/********************************************************************
* 名稱 : Main()
* 功能 : 主函數
***********************************************************************/
void main()
{
uint testnum;
EA = 0;
Timer0_Init(); //定時器0初始化
EA = 1;
RW=0;
L1602_init();
dis_init();
write_1602com(0x85);
write_1602dat(0xdf);
write_1602com(0x80);
……………………
…………限于本文篇幅余下代碼請從51黑下載附件…………

復制代碼

久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费