精品成人国产,久久久夜色,日韩免费在线播放

void InfraredReception()
{
if(CMP2OUT==0){ON_Flag==1;return;}
//if(T433_OK==1){return;}
if(mm==24)
{
mm=0;
if(++mm1<6)
{
T433_Num=0;
for(char i=4; i>0; i--)
{
T_Data[i] = data;
}
T_Data[0] = data; // 存入最新數據
for(char i=4; i>0; i--)
{
if(T_Data[i] == T_Data[0])
{
T433_Num++;
}
}
}
if(T433_Num>2)
{
addr=(T_Data[0]>>8)&0xFFFF;
if(addr==0xFFFF)
{
T433_OK=1;
value=T_Data[0]&0x0f;
}
}
Flag_RecOne=0;
}
if(INTEDG==0)//下降沿時計數器清0，開始計時
{
num=0;//計數器清0
TMR2=0;//定時器清0
INTEDG=1;//改為上升沿
}
else//下面是當上升沿時做的事
{
INTEDG=0;//下降沿。
Time=num*62;//62.5us定時器中斷，，計算下~上的時間
if(Flag_RecOne==0)
{
if((Time>11000) && (Time<12500))//引導碼，9ms低加4.5ms高
{
Flag_RecOne=1;
data=0;
mm=0;
}else
{
data=0;
}
}
if(Flag_RecOne==1)
{
if((Time>320) && (Time<460))//置1， 0.56ms低加1.68ms高
{
//data[(unsigned char)(mm/8)]=(data[(unsigned char)(mm/8)]>>1)|0x80;
data=(data << 1)|0x00000001;
mm++;
}
if((Time>1100) && (Time<1250))//置0， 0.56ms低加0.56ms高
{
//data[(unsigned char)(mm/8)]=(data[(unsigned char)(mm/8)]>>1) & 0x7f;
data=data << 1;
///RB4 = 1; //測試 0.56ms低加0.56ms高是否通過
mm++;
}
}
}
Time=0;
}
/***********************************************************
中斷服務函數
***********************************************************/
void interrupt Isr_Timer()
{
if(INTF)//外部中斷
{
InfraredReception();
INTF=0;
}
if (TMR2IF)
{ TMR2IF = 0; //若只使能了一個中斷源,可以略去判斷
num++;
if((Flag_0E==1)&&(ON==1))
{
num1++;
}
if (++MainTime >= 32)
{
MainTime = 0;
B_MainLoop = 1;
}
}
else
{
PIR1 = 0;
}
}
void WorkSleep()
{
#if (0 != C_KEY_WAKEUP)
OSCCON = 0X70; //配置振蕩為8M
INTCON = 0; //;關斷ADC模塊及中斷使能；
PIE1 = 0;
PIE2 = 0;
PIR1 = 0;
PIR2 = 0;
T2CON = 0;
ADCON0 = 0; //關閉所有模塊
ADCON1 = 0;
CMP1CON0 = 0;
CMP2CON0 = 0;
PWMCON0 = 0;
//進入休眠前關掉所有功能模塊,以降低休眠電流
KEYCON0=0;
KEYCON2=0;
TRISA = 0B00000001; //關閉所有輸出，RA0口做喚醒輸入
PORTA = 0B00000000;
WPUA = 0B00000001; //RA0 開上拉電阻
IOCA = 0B00000001; //允許RA0的IO電平變化中斷
RAIE = 1; //允許PORTA的IO電平變化中斷
PEIE = 1; //要用RORTA中斷喚醒，則PEIE必須設為1
//進入休眠前,必須固定口線電平,這兒全部輸出低電平,并關閉所有上拉電阻
RAIF = 0;
TRISB = 0;
PORTB = 0;
WPUB = 0B00000000;
//進入休眠模式,觸摸允許喚醒的按鍵后恢復正常工作
SystemEnterSleep();
if(RAIF)
{
RAIF = 0;
PORTA;
}
//休眠被喚醒,重新配置中斷等SFR,使系統進入正常工作
Init_System();
#endif
}
/***********************************************************
主循環
***********************************************************/
void main()
{
Init_System();
Init();
while (1)
{
if (B_MainLoop)
{
if(++num2>30)//消RGB鍵抖動，否則按一次跳變好幾下
{
//T433_OK=0;
if((ledFlag==4)&&(Flag_CS==1)){Touch_JianBian();Flag_CS=0;};
num2=0;
}
B_MainLoop = 0;
CLRWDT();
CheckTouchKey();
Refurbish_Sfr();
KeyServer();
if(ON_Flag==1){//關433
if(++mm4>200)
{ WorkSleep();
//TRISA = 0b00000011;//RA0引腳被配置為輸入
//PORTA = 0b00000011;
//PWMCON0 &= ~(0b00011111);
mm4=0;
ON_Flag=0;
}
}
if(RGB_Flag==1)//混合漸變
{ mm2++;
if((mm2>5)&&(ledFlag==12)){Led_Set();mm2=0;}
if(mm2>700)
{
if(ledFlag==13){Touch_JianBian();}
mm2=0;
}
}
}
DingShi();
if(T433_OK==1)//調433鍵處理函數
{
T433Server();
value=0xFE;
Flag_RecOne=0;
mm1=0;
T433_OK=0;
}
if(CMP2OUT==0){ON_Flag==1;}
//比較器，小于閥值
}
}
void DingShi()
{ if(ON==1)
{
if(T_Flag==1)//定時30分
{
if(num1>=28800000)
{
//PWMCON0 &= ~(0b00011111);
ON_Flag=1;
ON=0;
num1=0;
Flag_0E=0;
T_Flag=0;
}
}
if(T_Flag==2)//定時1H
{
if(num1>=57600000)
{
//PWMCON0 &= ~(0b00011000);
ON_Flag=1;
ON=0;
num1=0;
Flag_0E=0;
T_Flag=0;
}
}
if(T_Flag==3)//定時2H
{
if(num1>=115200000)
{
//PWMCON0 &= ~(0b00011000);
ON_Flag=1;
ON=0;
num1=0;
Flag_0E=0;
T_Flag=0;
}
}
if((T1S_Flag==1)&&(num1>600))//配合case 0x0E:閃一下
{
if(ledFlag==1){set_pwm_duty_cycle(pwm,0,0,0,0);}
else if(ledFlag==2){set_pwm_duty_cycle(0,pwm,0,0,0);}
else if(ledFlag==3){set_pwm_duty_cycle(pwm,pwm,0,0,0);}
else if(ledFlag==5){set_pwm_duty_cycle(pwm_sleep,pwm_sleep,0,0,0);}
else if(ledFlag==9){set_pwm_duty_cycle(0,0,0,0,pwm_R);}
else if(ledFlag==10){set_pwm_duty_cycle(0,0,pwm_G,0,0);}
else if(ledFlag==11){set_pwm_duty_cycle(0,0,0,pwm_B,0);}
else if(ledFlag==12){RGB_Flag=1;}
else if(ledFlag==4){set_pwm_duty_cycle(0,0,pwm_G,pwm_B,pwm_R);}
T1S_Flag=0;
}
}
}
void Touch_TiaoGuang()
{
if(ledFlag==4)
{ pwm_R = (R * brightness) / 100;
pwm_B = (B * brightness) / 100;
pwm_G = (G * brightness) / 100;
set_pwm_duty_cycle(0,0,pwm_G,pwm_B,pwm_R);
}
if(ledFlag==9)
{ pwm_R = (R1 * brightness) / 100;
set_pwm_duty_cycle(0,0,0,0,pwm_R);
}
if(ledFlag==10)
{ pwm_G = (G1 * brightness) / 100;
set_pwm_duty_cycle(0,0,pwm_G,0,0);
}
if(ledFlag==11)
{ pwm_B = (B1 * brightness) / 100;
set_pwm_duty_cycle(0,0,0,pwm_B,0);
}
if((ledFlag==13)||(ledFlag==12))
{
set_pwm_duty_cycle(0,0,0,0,10);
}
}
void Touch_JianBian()
{
switch (RGB_NUM)
{
case 0:
{
R=255;
G=255;
B=0;
RGB_NUM=1;
break;}
case 1:
{
R=80;
G=255;
B=0; // 紅綠
RGB_NUM=2;
break;}
case 2:
{
R=34;
G=139;
B=34; // 紅綠+
RGB_NUM=3;
break;}
case 3:
{
R=0; // 綠+++
G=255;
B=0;
RGB_NUM=4;
break;}
case 4:
{
B=124; // 青
G=252;
R=0;
RGB_NUM=5;
break;}
case 5:
{
B=255;// 紅0綠--藍+++
G=255;
R=0;
RGB_NUM=6;
break;}
case 6:
{
B=255;
G=120;
R=0;
RGB_NUM=7;
break;}
case 7: // 藍+
{
B=255;
G=0;
R=0;
RGB_NUM=8;
break;}
case 8:
{R=138; // 淺紅
G=43;
B=226;
RGB_NUM=9;
break;}
case 9:
{B=127;
G=0;
R=255; // 桃紅
RGB_NUM=10;
break;}
case 10:
{R=255; // 紅藍+
G=0;
B=255;
RGB_NUM=11;
break;}
case 11:
{R=255; // 紅
G=0;
B=0;
RGB_NUM=0;
break;}
}
pwm_R = (R * brightness) / 100;
pwm_B = (B * brightness) / 100;
pwm_G = (G * brightness) / 100;
set_pwm_duty_cycle(0,0,pwm_G,pwm_B,pwm_R);
}

復制代碼

久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费