STM32 ADC采集，DMA傳輸 DMA中斷處理

ID:324620 · 發表于 2018-5-7 22:13

//============================================
//函數名稱:ADC1_Mode_Config(void)
//功能描述:配置ADC1的工作模式為MDA模式
//輸入:無
//輸出:無
//============================================
void ADC1_Mode_Config(void)
{
DMA_InitTypeDef DMA_InitStructure;
ADC_InitTypeDef ADC_InitStructure;
/* DMA channel1 configuration */
DMA_DeInit(DMA1_Channel1);
DMA_InitStructure.DMA_PeripheralBaseAddr = ADC1_DR_Address; //ADC地址
DMA_InitStructure.DMA_MemoryBaseAddr = (u32)&ADC_ConvertedValue; //內存地址 ADC_ConvertedValue[15]一個數組
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;
DMA_InitStructure.DMA_BufferSize = 15;
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable; //外設地址固定
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable; //內存地址自加
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord; //半字
DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
DMA_InitStructure.DMA_Mode = DMA_Mode_Circular; //循環傳輸
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;
DMA_Init(DMA1_Channel1, &DMA_InitStructure);
/* Enable DMA channel1 */
DMA_Cmd(DMA1_Channel1, ENABLE);
DMA_ITConfig(DMA1_Channel1,DMA_IT_TC,ENABLE); //傳輸結束中斷
/* ADC1 configuration */
ADC_InitStructure.ADC_Mode = ADC_Mode_Independent; //獨立ADC模式
ADC_InitStructure.ADC_ScanConvMode = DISABLE ; //禁止掃描模式，掃描模式用于多通道采集
ADC_InitStructure.ADC_ContinuousConvMode = ENABLE; //開啟連續轉換模式，即不停地進行ADC轉換
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_None; //不使用外部觸發轉換
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right; //采集數據右對齊
ADC_InitStructure.ADC_NbrOfChannel = 1; //要轉換的通道數目1
ADC_Init(ADC1, &ADC_InitStructure);
/*配置ADC時鐘，為PCLK2的8分頻，即9MHz*/
RCC_ADCCLKConfig(RCC_PCLK2_Div8);
/*配置ADC1的通道11為55. 5個采樣周期，序列為1 */
ADC_RegularChannelConfig(ADC1, ADC_Channel_8, 1, ADC_SampleTime_55Cycles5);
/* Enable ADC1 DMA */
ADC_DMACmd(ADC1, ENABLE);
/* Enable ADC1 */
ADC_Cmd(ADC1, ENABLE);
/*復位校準寄存器 */
ADC_ResetCalibration(ADC1);
/*等待校準寄存器復位完成 */
while(ADC_GetResetCalibrationStatus(ADC1));
/* ADC校準 */
ADC_StartCalibration(ADC1);
/* 等待校準完成*/
while(ADC_GetCalibrationStatus(ADC1));
/* 由于沒有采用外部觸發，所以使用軟件觸發ADC轉換 */
ADC_SoftwareStartConvCmd(ADC1, ENABLE);
}
//============================================
//函數名稱:DMA1_Channel1_IRQHandler
//功能描述:DMA中斷對AD采集值平均濾波
//輸入:無
//輸出:無
//============================================
void DMA1_Channel1_IRQHandler(void)
{
BYTE i;
WORD ADC_ConvertedValue_TEMP=0;
for(i=0;i<15;i++)
{
ADC_ConvertedValue_TEMP += ADC_ConvertedValue; } ADC_ConvertedValue_average = ADC_ConvertedValue_TEMP/15; //全局變量ADC_ConvertedValue_average DMA_ClearITPendingBit(DMA1_IT_TC1); DMA_ClearFlag(DMA1_FLAG_TC1);}
//============================================//函數名稱:void GPIO_Configuration(void)//功能描述:ADC引腳配置//輸入:無//輸出:無//============================================void GPIO_Configuration(void){ GPIO_InitTypeDef GPIO_InitStructure; //=======================ADC通道配置======================== GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AIN; GPIO_Init(GPIOB, &GPIO_InitStructure); // PB0,輸入時不用設置速率}
//============================================//函數名稱:void NVIC_Configuration(void)//功能描述:中斷配置//輸入:無//輸出:無//============================================void NVIC_Configuration(void){ NVIC_InitTypeDef NVIC_InitStructure; /* Configure the NVIC Preemption Priority Bits */ NVIC_PriorityGroupConfig(NVIC_PriorityGroup_0); NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0; NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_InitStructure.NVIC_IRQChannel = DMA1_Channel1_IRQn; NVIC_Init(&NVIC_InitStructure); }