16燈搖搖棒單片機程序與制作資料

ID:488191 · 發(fā)表于 2019-5-28 22:59

#include <AT89X52.h>
#define uchar unsigned char
#define uint unsigned int //宏定義
#define KEY P3_7 //定義畫面切換按鍵
uchar KY; //KY作用在后面說明
uchar disp; //顯示漢字指針
uchar pic=0,num=0; //pic為按鍵次數；num為中斷次數
uchar code love[] = {
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x3F,0x00,0x20,0x00,0x20,0x00,0x20,
0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,0x0F,
0x04,0x10,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x04,0x10,0xF8,0x0F,0x00,0x00,
0x00,0x00,0x00,0x00,0xFE,0x07,0x00,0x08,0x00,0x10,0x00,0x20,0x00,0x20,0x00,0x10,
0x00,0x08,0xFE,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x3F,0x82,0x20,0x82,0x20,
0x82,0x20,0x82,0x20,0x82,0x20,0x82,0x20,0x82,0x20,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*LOVE*/
};
uchar code loveyou[] = {
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x78,0x00,0xFC,0x00,0xFE,0x01,0xFE,0x03,0xFE,0x07,0xFE,0x0F,0xFE,0x1F,0xFC,0x3F,
0xF8,0x7F,0xFC,0x3F,0xFE,0x1F,0xFE,0x0F,0xFE,0x07,0xFE,0x03,0xFE,0x01,0xFC,0x00,
0x78,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*心形圖案*/
};
uchar code hehe[] = {
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0x01,0x40,0x01,0xC0,0x01,0x00,0x00,0x00,0x00,
0xF0,0x0F,0x08,0x10,0x04,0x20,0x00,0x00,0x00,0x00,0xF0,0x3F,0x08,0x00,0x04,0x00,
0x04,0x00,0x04,0x00,0x08,0x00,0xF0,0x3F,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x20,
0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x00,0x00,0x00,0xF0,0x3F,0x08,0x00,0x04,0x00,
0x04,0x00,0x04,0x00,0x08,0x00,0xF0,0x3F,0x00,0x00,0x00,0x00,0x04,0x20,0x08,0x10,
0xF0,0x0F,0x00,0x00,0x00,0x00,0xC0,0x01,0x40,0x01,0xC0,0x01,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*呵呵o(∩_∩)o圖案*/
};
unsigned char code hanzi[] = {
//-- 歡 --
0x04,0x10,0x34,0x08,0xC4,0x06,0x04,0x01,
0xC4,0x82,0x3C,0x8C,0x20,0x40,0x10,0x30,
0x0F,0x0C,0xE8,0x03,0x08,0x0C,0x08,0x10,
0x28,0x60,0x18,0xC0,0x00,0x40,0x00,0x00,
//-- 迎 --
0x40,0x00,0x42,0x40,0x44,0x20,0xC8,0x1F,
0x00,0x20,0xFC,0x47,0x04,0x42,0x02,0x41,
0x82,0x40,0xFC,0x7F,0x04,0x40,0x04,0x42,
0x04,0x44,0xFE,0x63,0x04,0x20,0x00,0x00,
//-- 使 --
0x40,0x00,0x20,0x00,0xF8,0xFF,0x07,0x00,
0x04,0x80,0xF4,0x43,0x14,0x45,0x14,0x29,
0x14,0x19,0xFF,0x17,0x14,0x21,0x14,0x21,
0x14,0x41,0xF6,0xC3,0x04,0x40,0x00,0x00,
//-- 用 --
0x00,0x80,0x00,0x60,0xFE,0x1F,0x22,0x02,
0x22,0x02,0x22,0x02,0x22,0x02,0xFE,0x7F,
0x22,0x02,0x22,0x02,0x22,0x42,0x22,0x82,
0xFF,0x7F,0x02,0x00,0x00,0x00,0x00,0x00,
};
/*****函數聲明*****/
void display1_ltor(void);
void display2_ltor(void);
void display2_rtol(void);
void display3(void);
void display4(void);
/*****n（us）延時子程序*****/
void DelayUs(uint N)
{
uint x;
for(x=0; x<=N;x++);
}
/*****中斷服務程序*****/
void intersvr0(void) interrupt 0
{
;
KY=~KY; //每個搖動來回水銀開關會在擺幅兩端分別產生下降沿中斷，只提取其中一次（從左向右搖才顯示）
if(KY==0)
{
num++; //計算中斷次數
switch(pic) //選擇畫面
{
case 0:{display1_ltor();}break;
case 1:{display2_ltor();}break;
case 2:{display3();}break;
case 3:{display4();}break;
default:{display1_ltor();}
}
}
}
/*****顯示子程序1（漢字）*****/
void display1_ltor(void)
{
uchar i;
if(num>10){disp++;num=0;} //12個漢字分為3次顯示完（每次顯示4個），每中斷10次切換
if(disp>2)disp=0;
DelayUs(5200); //此處延時時間依各硬件差別而各不相同，試著調整使得顯示內容居中即可
for(i=0;i<64;i++)
{
P0=~hanzi[disp*128+i*2];
P2=~hanzi[disp*128+i*2+1];
DelayUs(100);
}
}
/*****顯示子程序2（LOVE）*****/
void display2_ltor(void)
{
uchar i;
DelayUs(4000);
for(i=0;i<64;i++)
{
P0=~love[i*2];
P2=~love[i*2+1];
DelayUs(140);
}
}
/*****顯示子程序3（心形圖案）*****/
void display3(void)
{
uchar i;
DelayUs(4000);
for(i=0;i<64;i++)
{
P0=~loveyou[i*2];
P2=~loveyou[i*2+1];
DelayUs(120);
}
}
/*****顯示子程序4（呵呵o(∩_∩)o圖案）*****/
void display4(void)
{
uchar i;
DelayUs(4000);
for(i=0;i<64;i++)
{
P0=~hehe[i*2];
P2=~hehe[i*2+1];
DelayUs(120);
}
}
/*****主函數*****/
void main(void)
{
IT0=1;
EX0=1;
EA=1; //開中斷，下降沿中斷
KY=0;
KEY=1;
while(1) //主程序中只檢測按鍵
{
if(KEY==0) //畫面切換鍵按下
{
DelayUs(10000); //按鍵去抖
if(KEY==0);
pic++;
while(KEY==0);
}
if(pic>3)pic=0;
}
}
/*****END*****/