基于STM32藍牙打印機源程序

ID:387744 · 發表于 2019-7-8 16:34

#include "motor.h"
#include "delay.h"
#include "timer.h"
#include "printer.h"
#include "led.h"
#include "usart.h"
#include "uart_font.h"
#include "flash.h"
#include "dma.h"
#include <string.h>
u8 const test_str[]="\r\n\

void updata_font()//更新字庫
{
      u8 i;
      u8 group = 0;
      u32 write_addr = 0;

      LED1 = 0;
      uart1_printf("flash init ok!\n");

//       spi_flah_erase_chip();
      for (i=0; i<148; i++)
      {
            spi_flash_erase_sector(i);
      }

      uart1_printf("flash erase ok!\n");

      while (1)
      {
               if (font_buffer[group].uart_rev_len)
               {
                     spi_flash_write_nocheck((u8*)font_buffer[group].data_buf, write_addr,
                                                                              font_buffer[group].uart_rev_len);

//                      uart1_printf("pg_addr:%-6d ok\n",write_addr);

                     write_addr += font_buffer[group].uart_rev_len;

                     font_buffer[group].uart_rev_len = 0;

                     group = !group;
               }

            if (key_scan() == 1)
            {
                     break;
            }
      }
}

int main()
{
      u32 cnt = 0;
      u16 rx_flg = 0;

      init_delay(72);

      init_motor_gpio();
      init_printer_gpio();

      usart2_init(36, 9600);       //串口2接藍牙模塊
      bluetooth_swi(1);//打開藍牙模塊

      DMAx_Config(DMA1_Channel7, (u32)&USART2->DR, (u32)(uart_buffer.tx_buf));

      init_usart1(72, 921600);//串口1 燒錄字庫
      DMAx_Config(DMA1_Channel4, (u32)&USART1->DR, (u32)uart1_tx_buf);

      init_key();
      init_led();
      init_timer3_int(1100-1,72-1);//800us溢出一次
      spi_flash_init();

      if (spi_flash_read_id() != W25Q64)
      {
            uart_printf("flash error!\n");

            while (1)
            {
                     ;
            }
      }

      if (key_scan() == 1)
      {
            updata_font();
      }
      else
      {
            while (1)
            {
                     if (key_scan() == 1)//按下按鍵，繼續往下執行
                     {
                              break;
                     }
            }
      }
      BUZZ = 1;
      delay_ms(200);
      BUZZ = 0;
      uart_printf("The printer is ready.\n");
      uart_buffer.rx_len = rx_flg;
      while (1)
      {
            printer_updata();//打印機更新數據
            printer_updata_pic();

            if (uart_buffer.rx_len != rx_flg)//防止重復執行這里
            {
                     if (uart_buffer.rx_len > 0)       //收到數據
                     {
                              uart_printf("OK:printing ...\r\n");
                              bluetooth_data_formatting((u8*)uart_buffer.rx_buf);
                              uart1_printf("%s", uart_buffer.rx_buf);
                              printer_status = PRINT_TEXT;
                              print_updata_text_flg = 1;
                              printer_updata();             //打印機更新數據

                              TIM3->EGR = 1<<0;             /* 軟件更新 */
                              TIM3->SR = 0;                      /* 清0狀態標識 */

                              TIM3->CR1 |= 0x01;
                     }
                     rx_flg = uart_buffer.rx_len;
            }

            if ((TIM3->CR1 & 1) == 0)//如果當前沒有打印
            {
                     if (++cnt == 600000)
                     {
                              cnt = 0;
                     }

                     LED1 = cnt<60000 ? 0 : 1;

                     if (key_scan() == 1)
                     {
                              strcpy((char*)uart_buffer.rx_buf, (char*)test_str);

                              bluetooth_data_formatting((u8*)uart_buffer.rx_buf);
                              uart_printf("OK:printing ...\r\n");

                              printer_status = PRINT_TEXT;
                              print_updata_text_flg = 1;
                              printer_updata();             //打印機更新數據

                              TIM3->EGR = 1<<0;             /* 軟件更新 */
                              TIM3->SR = 0;                      /* 清0狀態標識 */

                              TIM3->CR1 |= 0x01;
                     }
            }
      }//end while(1)
}

ID:1 · 發表于 2019-7-8 20:05

本帖需要重新編輯補全電路原理圖,源碼,詳細說明與圖片即可獲得100+黑幣(帖子下方有編輯按鈕)

帳號		自動登錄	找回密碼
密碼			立即注冊

久久久久久久999_99精品久久精品一区二区爱城_成人欧美一区二区三区在线播放_国产精品日本一区二区不卡视频_国产午夜视频_欧美精品在线观看免费

基于STM32藍牙打印機源程序