我想用16*16的點陣模擬電梯運行時的樓層顯示，但是寫出來的程序一直顯示不出來，按按鍵也沒反應，程序如下：（用4片595控制點陣）
#include<reg51.h>
#include<intrins.h>
#define uchar unsigned char
#define uint unsigned int
uchar code NUM_HANG[]={
0x80,0x00,0x40,0x00,0x20,0x00,0x10,0x00,0x08,0x00,0x04,0x00,0x02,0x00,0x01,0x00,
0x00,0x80,0x00,0x40,0x00,0x20,0x00,0x10,0x00,0x08,0x00,0x04,0x00,0x02,0x00,0x01,};
uchar code Table_of_Digits[8][32]=
{//數字8的字碼
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xC0,0x02,0x20,0x02,0x20,
0x03,0xE0,0x02,0x20,0x02,0x20,0x01,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
},
//數字7的字碼
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xE0,0x00,0x20,0x00,0x20,
0x00,0x40,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
},
//數字6的字碼
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xC0,0x02,0x20,0x03,0xC0,
0x02,0x20,0x02,0x20,0x01,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
},
//數字5的字碼
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0xE0,0x02,0x00,0x03,0xC0,
0x00,0x20,0x00,0x20,0x03,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
},
//數字4的字碼
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x00,0xC0,0x01,0x40,
0x02,0x40,0x07,0xE0,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
},
//數字3的字碼
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xC0,0x02,0x20,
0x00,0xC0,0x00,0x20,0x02,0x20,0x01,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
},
//數字2的字碼
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xC0,0x02,0x20,0x00,0x20,
0x00,0x40,0x00,0x80,0x01,0x00,0x03,0xE0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
},
//數字1的字碼
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x03,0x80,0x00,0x80,0x00,0x80,
0x00,0x80,0x00,0x80,0x00,0x80,0x03,0xE0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
},
};
uchar i=0,t=0,j=0,a=0,m=0,n=0;
char offset=0;
static int Current_floor=0,Pressed_Key_up=0, Pressed_Key_down=0,b=0,c=0,max=0,min=0;// Current_floor當前樓層 Pressed_Key_up 上升請求 Pressed_Key_down 下降請求
int flag;
int floor_up[8]={9,9,9,9,9,9,9,9};
int floor_down[8]={0,0,0,0,0,0,0,0};
sbit KEY1=P2^0; //定義按鍵P1口
sbit KEY2=P2^1;
sbit KEY3=P2^2;
sbit KEY4=P2^3;
sbit KEY5=P2^4;
sbit KEY6=P2^5;
sbit KEY7=P2^6;
sbit KEY8=P2^7;
sbit SPEAK=P0^7; //定義蜂鳴器
sbit SCK=P3^6;
sbit LCK=P3^5;
sbit SDI=P3^4;
void Key_up_comparison(); //函數聲明，把floor_up[]從小到大排列
void Key_down_comparison(); //把floor_down[]從大到小排列
void max_min_comparison(); //比較出floor_up[]的最大值（max）和flor_down[]的最小值（min）
void HC595_Send(uchar dat1,uchar dat0,uchar dat2,uchar dat3);
void main() //主函數
{
SPEAK=0;
TMOD=0x01; //T0方式
TH0=(-6000)/256; //6ms定時
TL0=(-6000)%256;
IT0=1;
IE=0x83;
TR0=1;
ET0=1;
EA=1;
Pressed_Key_up=floor_up[0];
while(1)
{
Key_up_comparison();
Key_down_comparison();
max_min_comparison();
}
}
void LED_Display() interrupt 1 //進入中斷，顯示樓層 interrupt1
{
TH0=(-6000)/256; //6ms
TL0=(-6000)%256;
Pressed_Key_up=floor_up[0];
Pressed_Key_down=floor_down[0];
if(flag==1) //上升標志
{
if(Pressed_Key_up!=9)
{
if(Pressed_Key_up>Current_floor)
{
m=(7-Current_floor)+i;
for(n=0;n<32;n=n+2) //一共有16行，所以刷16次
{
HC595_Send(~Table_of_Digits[m][n],~Table_of_Digits[m][n+1],NUM_HANG[n],NUM_HANG[n+1]);
}
if(++i==8)
{
i=0;
}
if(++t==250)
{
t=0;
++Current_floor;
}
}
else if(Pressed_Key_up<Current_floor);
else if(Pressed_Key_up==Current_floor) //到達請求樓層
{
m=(7-Current_floor)+i;
for(n=0;n<32;n=n+2) //一共有16行，所以刷16次
{
HC595_Send(~Table_of_Digits[m][n],~Table_of_Digits[m][n+1],NUM_HANG[n],NUM_HANG[n+1]);
}
if(++i==8)
{
i=0;
}
SPEAK=~SPEAK; //蜂鳴器響
if(++t==250)
{
t=0;
if(Current_floor=Pressed_Key_up)
{
Current_floor=Pressed_Key_up;
if(Current_floor==max)
{
flag=0;
}
floor_up[0]=9;
}
}
}
}
else if(Pressed_Key_up==9) //無按鍵按下，即無請求，則掃描當前樓層
{
m=(7-Current_floor)+i;
for(n=0;n<32;n=n+2) //一共有16行，所以刷16次
{
HC595_Send(~Table_of_Digits[m][n],~Table_of_Digits[m][n+1],NUM_HANG[n],NUM_HANG[n+1]);
}
if(++i==8)
{
i=0;
}
if(++t==250)
{
t=0;
}
}
}
else if(flag==0)
{
if(Pressed_Key_down!=0) //有下降的請求
{
if(Pressed_Key_down>Current_floor);
else if(Pressed_Key_down<Current_floor) //下降的顯示
{
m=(7-Current_floor)+i+offset;
for(n=0;n<32;n=n+2) //一共有16行，所以刷16次
{
HC595_Send(~Table_of_Digits[m][n],~Table_of_Digits[m][n+1],NUM_HANG[n],NUM_HANG[n+1]);
}
if(++i==8)
{
i=0;
}
if(++t==25)
{
t=0;
if(--offset==-8)
{
offset=0;
--Current_floor;
}
}
}
else if(Pressed_Key_down==Current_floor) //到達請求的樓層
{
m=(7-Current_floor)+i;
for(n=0;n<32;n=n+2) //一共有16行，所以刷16次
{
HC595_Send(~Table_of_Digits[m][n],~Table_of_Digits[m][n+1],NUM_HANG[n],NUM_HANG[n+1]);
}
if(++i==8)
{
i=0;
}
SPEAK=~SPEAK; //蜂鳴器響
if(++t==250)
{
t=0;
if(Current_floor=Pressed_Key_down)
{
Current_floor=Pressed_Key_down;
if(Current_floor==min)
{
flag=1;
}
floor_down[0]=0;
}
}
}
}
else if(Pressed_Key_down==0) //無按鍵按下，即請求，則掃描顯示當前樓層
{
m=(7-Current_floor)+i;
for(n=0;n<32;n=n+2) //一共有16行，所以刷16次
{
HC595_Send(~Table_of_Digits[m][n],~Table_of_Digits[m][n+1],NUM_HANG[n],NUM_HANG[n+1]);
}
if(i==8)
{
i=0;
}
if(t==250)
{ t=0;}
}
}
}
void Key_detection() interrupt 0 //按下按鍵，進入外部中斷，將上升請求和下降請求放入數組中去，并且判斷標志位flag
{
// P0=0xff;
i=0; //按鍵消抖
if(KEY1==0) j=8;
else if(KEY2==0) j=7;
else if(KEY3==0) j=6;
else if(KEY4==0) j=5;
else if(KEY5==0) j=4;
else if(KEY6==0) j=3;
else if(KEY7==0) j=2;
else if(KEY8==0) j=1;
if(j>Current_floor) //將上升請求放入數組中
{
if(floor_down[0]==0)
flag=1;
floor_up[b++]=j;
if(b==8)
b=0;
}
else if(j<Current_floor) //將下降請求放入數組
{
if(floor_up[0]==9)
flag=0;
floor_down[c++]=j;
if(c==8)
c=0;
}
else if(j==Current_floor);
}
void Key_up_comparison() //把floor_up[]按從小到大的順序排列
{
int a1,a2,a3=0;
for(a2=0;a2<7;a2++)
{
for(a1=0;a1<7;++a1)
{
if(floor_up[a1]>floor_up[a1+1])
{
a3=floor_up[a1];
floor_up[a1]=floor_up[a1+1];
floor_up[a1+1]=a3;
}
if(floor_up[a1]==floor_up[a1+1])
floor_up[a1+1]=9;
}
}
}
void Key_down_comparison() //把floor_down[]按從大到小的順序排列
{
int a1,a2,a3=0;
for(a2=0;a2<7;a2++)
{
for(a1=0;a1<7;++a1)
{
if(floor_down[a]<floor_down[a1+1])
{
a3=floor_down[a1];
floor_down[a1]=floor_down[a1+1];
floor_down[a1+1]=a3;
}
if(floor_down[a1]=floor_down[a1+1])
floor_down[a1+1]=0;
}
}
}
void max_min_comparison() //求出 floor_up[]的最大（max）和floor_down[]的最小(min)
{
int j;
for(j=1;j<7;j++)
if(floor_down[j]==0);
else if(floor_down[j+1]==0)
min=floor_down[j];
else if(floor_down[j]>floor_down[j+1])
min=floor_down[j+1];
else min=floor_down[j];
for(j=1;j<7;j++)
if(floor_up[j]==9);
else if(floor_up[j+1]==9)
max=floor_up[j];
else if(floor_up[j]<floor_up[j+1])
max=floor_up[j+1];
else max=floor_up[j];
}
void HC595_Send(uchar dat1,uchar dat0,uchar dat3,uchar dat2) //顯示程序
{
uchar i;
SCK=1;
LCK=1;
for(i=0;i<8;i++)
{
SDI=dat0&0x01; //從高位到低位
dat0>>=1;
SCK=0;
_nop_();
_nop_();
SCK=1;
_nop_();
_nop_();
}
for(i=0;i<8;i++)
{
SDI=dat1&0x01; //從高位到低位
dat1>>=1;
SCK=0;
_nop_();
_nop_();
SCK=1;
_nop_();
_nop_();
}
for(i=0;i<8;i++)
{
SDI=dat2&0x01; //從高位到低位
dat2>>=1;
SCK=0;
_nop_();
_nop_();
SCK=1;
_nop_();
_nop_();
}
for(i=0;i<8;i++)
{
SDI=dat3&0x01; //從高位到低位
dat3>>=1;
SCK=0;
_nop_();
_nop_();
SCK=1;
_nop_();
_nop_();
}
LCK=0; //下面是輸出時鐘
_nop_();
_nop_();
LCK=1;
_nop_();
_nop_();
} |
QQ好友和群
QQ空間
騰訊微博
騰訊朋友
收藏
淘帖
頂
踩
